Industry standards and verification methods for steam curing pallets
- Date:2025-12-26
Industry standards and verification methods for steam curing pallets
At present, there are no national or industry mandatory standards (such as GB, JC, JB) specifically for "steam curing pallets" in China. Their technical specifications are mainly based on enterprise practices, material performance benchmarks, and authoritative testing methods, forming a de facto industry consensus. The system is based on GMT glass fiber reinforced thermoplastic composite materials and achieves quality control through reproducible physical and chemical testing methods.
Industry standard status: no exclusive standards, technical benchmarks available
|Category | Current Situation Description|
|National standard | No independent standard. The related "Autoclaved Aerated Concrete slabs" (GB/T 15762-2020) only specifies finished slabs and does not involve requirements for pallet material, structure, or cyclic performance. |
|Industry standard | No building materials industry (such as JC/T) has released dedicated standards for steam curing pallets. The "Building Materials Industry Block Forming Machine" (JC/T 920-2011) only specifies equipment parameters (such as pallet size of 1400 × 750mm), without defining material properties. |
|Group Standards | No relevant group standards published by organizations such as the China Concrete and Cement Products Association and the China Building Materials Federation were found. |
|International standards | No international standards such as ISO, ASTM, etc. cover the specific technical requirements for "steam curing pallet" or "GMT pallet". The universal pallet standard (such as GB/T 3716-2023) is only applicable to logistics turnover and is not suitable for high temperature and high humidity conditions. |
|Enterprise Standard | Local mainstream manufacturers in Linyi (such as Shandong Juncheng) clearly define GMT pallet performance indicators (such as water absorption ≤ 0.5%, compressive strength ≥ 345MPa, and service life 6-10 years) in product descriptions, but have not publicly recorded them on the "National Enterprise Standard Information Public Service Platform", which is a non-public technical specification. |
Key conclusion: The "standard" of steam curing pallets is essentially a performance benchmark formed by industry practice, rather than a legal or administrative mandatory document.
Authoritative verification method: detection method system based on national standards
Although there are no exclusive standards, the industry widely adopts the material testing standards that have been released by the country as the verification basis, which is scientific and traceable
|Verification Project | Testing Method Standards | Qualification Requirements | Application Scenarios|
|Water absorption rate | GB/T 1034-2008 "Determination of Water Absorption of Plastics" | ≤ 0.5% (24-hour water immersion) | Determine material density to prevent expansion and deformation during steam curing|
|Compressive strength | GB/T 1448-2005 "Test Method for Compressive Properties of Fiber Reinforced Plastics" | ≥ 345 MPa | Ensure that it does not break under a heavy load of 10 tons|
|Hot deformation temperature | GB/T 1634.2-2004 "Determination of plastic deformation temperature under load" | ≥ 140 ° C (1.82MPa) | Verification of steam resistance at 180 ° C|
|Fiber structure | Microscopic observation (non-standard but universal) | Continuous glass fiber three-dimensional network structure, no powder shedding | On site identification of genuine GMT and inferior imitations|
|Fatigue resistance | GB/T 1451-2005 "Test method for impact performance of fiber-reinforced plastic simply supported beams" | No cracks after ≥ 2 million cycles | Simulated continuous operating life of loop|
|Weather resistance | GB/T 16422.2-2014 "Plastic laboratory light source exposure test method" | Mechanical retention rate ≥ 85% after UV aging for 1000 hours | Verification of long-term outdoor stability|
Authority testing: The above methods are adopted by national institutions such as the National Building Materials Testing Center, and the data can be certified and accepted by third parties.
On site rapid verification method (practical operation of Linyi Brick Factory)
Against the backdrop of a lack of standard documents, the Linyi region has developed an efficient, low-cost, and replicable on-site acceptance mnemonic, which has been adopted by over 90% of brick factories
|Method | Operation | Judgment Basis|
|Look at the fibers | Scrape the edge section of the pallet with a blade | True GMT: The fibers are like woven brocade, clear and continuous; Fake goods: gray powder peeling off, no structure|
|Measure water absorption | Drop water on the surface and let it stand for 1 minute | True GMT: Water droplets do not leak or spread; Fake goods: rapid penetration, discoloration|
|Listen to the sound | Tap the middle of the tray lightly with a metal object | True GMT: Clear as a bell, with a long aftertaste; Fake goods: dull sound like wood, no echo|
Three in one: Only when "clear fibers, no water seepage, and clear sound" are met simultaneously, can it be judged as a qualified GMT pallet.
Shandong Juncheng Plastic Sheet Co., Ltd. is located in Linyi City, Shandong Province. The company is a manufacturer of glass fiber pallets, fiber pallets, brick machine pallets, brick machine pallets, and PVC brick machine pallets. Contact address: Dazhuang Economic Development Zone, Yinan County, Shandong Province, China, Phone: 15069997770
The various information published on this website is for reference only and does not represent the position or viewpoint of this website. It does not constitute any investment, medical, legal or decision-making advice. Any actions taken by users based on the information on this website are at their own risk, and this website does not assume any direct or indirect responsibility. This website does not assume any responsibility for the authenticity, accuracy, completeness, or legality of its content.





